Toughened Glass Balustrades & Stainless Steel Posts

10mm Toughened, Polished Edged Glass with 304 & 316 Grade Stainless Steel Posts

GLASS SPECIFICATION

• 10mm thick Toughened, Safety Glass. (13mm Laminated available upon request. Please enquire)
• All edges are fully polished
• Corners are dubbed, rounded
• Glass Panel Height: 1000mm
• Glass Panel Width: Please select from the 13 sizes available (300mm – 1500mm)

Bespoke Sizes are available upon request. Enquire for pricing.

When the glass is fitted to the balustrade, the total height is 1100mm. There will be a 100mm gap at the bottom between the glass panel and the floor surface.

STAINLESS STEEL BALUSTRADE & CLAMP SPECIFICATION

• Material: High Quality Grade 304 & 316, Grit Marine Stainless Steel, (For outdoor use)
• Diameter: 42.4mm
• Height: 1100mm
• Bespoke height post sizes are available upon request
• Finishing: Flush top caps
• Base Plate: 304 steel 100mm Welded base, 316 steel 100mm welded base, with cover plate
• Clamps : 316 Stainless Steel Glass Clamps – D Type Round Back for 42.4mm balustrade to fit 10mm glass
• Clamps measure 61.5mm in length.
• Handrails and accessories are available. Refer to other listing. Price also supplied on request.

Each Balustrade consumes 85mm of space between each glass panel. (42mm pole diameter, plus 21.5mm each side for the connecting clamps, totaling 85mm).

Please read very important:

When calculating the size of the panels you require, remember to add 85mm to the width between each glass panel, (where the balustrade will stand). For example, two 800mm x 800mm glass panels, with two end balustrades and one centre joining balustrade will require a space of 1855mm, (85mm End Balustrade + 800mm Glazed Panel + 85mm Centre Balustrade + 800mm Glazed Panel + 85mm End Balustrade). Refer to the example diagram above. The 85mm measurement includes the 42mm Balustrade post diameter, plus 21.5mm either side for each clamp, (this is also the size of the gap between the glass panels and the balustrade post). The End Balustrades also requires 85mm, as the base plate will occupy this space. The glass panels sit 40mm inside each clamp. The total Clamp size is 61.5mm.

This listing is for 10mm toughened glass and stainless steel balustrade.
Please add each item you require to your shopping basket using the drop down menu at the top of the page, then check-out once all items have been selected.
If you order just glass panels, they do not come with balustrades as standard.
Please use the drop down menu to select the glass and balustrades you would like and add them to the basket separately.

Please contact our sales office for a postage quote if you want less than 4 pieces of Glass, or just Balustrade.

Fixings

Fixings and bolts are not supplied with systems. We recommend the following:-

• Steel – M10 Bolt Through / Drill & Tap
• Brick or Concrete – M10 Anchor Bolt / Thunder Bolt or Threaded Bar & Resin
• Wood – M10 Coach Screws / Bolts

*These fixtures are provided as a guide and may not be suitable for every application

Install Tips

Please be extremely careful when unpacking the glass panels, as the slightest nick on the edge of the glass may cause it to shatter. We recommend that customers leave the panels in the packaging until assembling into position. If for whatever reason, the panel does need to be left idle, (after unwrapping), it should be placed in a dust sheet or supported by a wooden rest. Glass Panels should never be left lying on a concrete floor, tiles or paving slabs, as again, the slightest scratch or chip can cause the panel to shatter.

When fitting the glass panels into position, place 100mm wooden blocks underneath to support the glass.

Installing balustrade posts to a solid foundation is essential.

We recommend a minimum fixing depth of 100mm for each post.

Place all posts in the desired position, leaving at least a 100mm gap from any ledges.

Use all fixing holes found on the base plates when fixing the balustrade into position.

Always allow enough time for the resin to set before proceeding with the installation of the glass panels. (for use on brick work or crumbling surfaces, we advise using Chem Fix resin).

Do not use power tools to tighten glass clamps or covers.